Microe PurePrecision Manuel d'utilisateur

Page 1PurePrecision™Tape and Glass Scale Installationfor OPS Series EncodersInstallation Manualand Reference GuideMicroE Systems • 125 Middlesex Turnp

Page 10Tape Scale, OPS Side/Top Mount ConfigurationsInstallation By Hand 4.Place the PurePrecision™Tape Scale against the mounting surface “D” referen

Page 11Tape Scale, OPS Side/Top Mount ConfigurationsInstallation By Hand 5.Install the PurePrecision Tape Scale along the remaining length of the moun

Page 12Tape Scale, OPS Side/Top Mount ConfigurationsInstallation By Hand 6.Once the scale is applied to the mounting surface, and before the blue prot

Page 13Tape Scale, OPS Side Mount ConfigurationInstallation By Mounted Applicator Tool 1.OPS Side Mounted Tape Scale Applicator Tool (Model Number: TS

Page 14Tape Scale, OPS Side Mount ConfigurationInstallation By Mounted Applicator Tool 3.Mount the Applicator Tool.Mount the Applicator Tool in the Se

Page 15Tape Scale, OPS Side Mount ConfigurationInstallation By Mounted Applicator Tool 5.Peel off a short section of bottom adhesive backing approxima

Page 16Tape Scale, OPS Side Mount ConfigurationInstallation By Mounted Applicator Tool 7.Insert a short section of tape scale into the tool, approxima

Page 17Tape Scale, OPS Side Mount ConfigurationInstallation By Mounted Applicator Tool 9.Move the tool in a steady motion to apply the tape scale.Push

Page 18Tape Scale, OPS Side Mount ConfigurationInstallation By Mounted Applicator Tool NOTE: After removing the blue protective film, the scale is rea

Page 19Tape Scale, OPS Top Mount ConfigurationInstallation by Hand Grip Applicator ToolReference arrows for Tool andtape scale orientation1.OPS Top Mo

Page 2Table of ContentsPurePrecision™Scale InstallationIntroductionIntroduction (Precautions, Patents, Manual Revisions) ...

Page 20Tape Scale, OPS Top Mount ConfigurationInstallation by Hand Grip Applicator Tool2.Hand Grip Applicator Tool mounting surface guide edges (conti

4.Preparing the tape scale for the applicator toolPurePrecision Tape Scales have 3 layers, blue protective film, steel scale, and adhesive backing. Th

Page 225.Feed the adhesive backing into the applicator toolInsert the backing film into the applicator tool. Tape Scale, OPS Top Mount ConfigurationIn

Page 23Tape Scale, OPS Top Mount ConfigurationInstallation by Hand Grip Applicator Tool7.Applying tape scale with the hand grip applicator toolOnce th

Page 24Tape Scale, OPS Top Mount ConfigurationInstallation by Hand Grip Applicator Tool8.Once the scale is applied to the mounting surface, and before

Page 25Linear Glass Scales, OPS Side and Top MountConfigurationsInstallation1.Mounting Surface PreparationInspect the mounting surface for any machini

Page 26Linear Glass Scales, OPS Top Mount ConfigurationsInstallation3.Mounting linear Glass Scales (with adhesive backing), Model Number PVGL-TMake su

Page 27Index and Limit Marker “Strip” PackagingIndex and Limit Marker InstallationStick-On Markers for PurePrecision Laser Tape II (HPTS-) and Perform

Page 28Index and Limit Marker InstallationStick-On Markers for PurePrecision Laser Tape II (HPTS-) and Performance and Value LinearGlass (PVGL-). (Not

Page 29Index and Limit Marker InstallationStick-On Markers for PurePrecision Laser Tape II (HPTS-) and Performance and ValueLinear Glass (PVGL-). (Not

Page 3PrecautionsFollow standard ESD precautions. Turn power off before connecting the sensor. Donot touch the electrical pins without static protecti

Page 30Index and Limit Marker InstallationStick-On Markers for PurePrecision Laser Tape II (HPTS-) and Performance and Value LinearGlass (PVGL-). (Not

Page 31End Cap Installation for Tape ScalesOptional1.Epoxy Setup• Mix the two-part epoxy and place it in a syringe or on the end of a stick. Do not us

Page 32Final Cleaning, Inspection and Cure TimeBefore using the encoder for servo control, clean the tape scale, index marker and limit markers using

Page 33Contacting MicroEMicroE Systems is a world leader in optical encoder technology withoffices in major industrial centers around the globe.To lea

Page 4OverviewThis manual applies to the installation of the following scale types.• PurePrecision Marker Tape II for OPS Series, Model HPMT-• PurePre

Page 5Pre-Installation Information and PrecautionsRead all instructions completely before beginning theinstallation process.The PurePrecision™Tape Sca

Page 6Design Guidelines1.Verify the tolerances of the scale's mounting surface given in the Interface Drawing.2.Verify the dimensions of the scal

Page 7Mounting Surface Preparation1.Inspect the mounting surface for any machining irregularities. MicroE Systems recommends a surface finishof better

Page 8Cutting the PurePrecision™Tape Scale 1.Uncoil the tape scale and cut it to the required length using shears.Note: check the interface drawing to

Page 9Tape Scale, OPS Side/Top Mount ConfigurationsInstallation By Hand 2.Removing/peeling the bottomadhesive liner. PurePrecision Tape Scales have 3